• Getting Started
    • Setting up your Slink-e
      • Setting up the serial port
      • Setting up the S-Link ports
      • Setting up the IR Ports
      • Setting up the Control-S port
      • Setting up the parallel port
      • Powering the Slink-e
      • Simple tests of Slink-e functionality
    • Low-Level Serial Command Interface
      • Port Send
      • Port Send End
      • Port Send Message
        • Disable port
        • Enable port
        • Send S-Link bit-mode
        • Set IR sampling period
        • Get IR sampling period
        • Set IR carrier frequency
        • Get IR carrier frequency
        • Set IR timeout period
        • Get IR timeout period
        • Set IR minimum message length
        • Get IR minimum message length
        • Set IR transmit ports
        • Get IR transmit ports
        • Set IR receive ports
        • Get IR receive ports
        • Set IR receive port polarities
        • Get IR receive port polarities
        • Set IR routing table
        • Get IR routing table
        • Set handshaking mode
        • Get handshaking mode
        • Set direction configuration
        • Get direction information
        • Sample port
        • Set baud rate
        • Get baud rate
        • Get version
        • Save defaults
        • Load defaults
        • Get serial number
        • Resume
        • Reset
      • Port receive
      • Port receive end
      • Port receive message
        • Port disabled
        • Port enabled
        • Transmission timeout
        • Illegal command
        • Receive error
        • Sampling period equals
        • Carrier frequency equals
        • Timeout period equals
        • Minimum message length equals
        • Transmit ports equals
        • Receive ports equal
        • Last receive port equals
        • Receive port polarities equal
        • Routing table equals
        • Invalid sample period
        • Handshaking mode equals
        • Direction configuration equals
        • Baud rate equals
        • Serial port receive buffer overflow
        • Serial port receive buffer overrun
        • Serial port receive framing error
        • Baud rate illegal
        • Version equals
        • Defaults loaded
        • Defaults saved
        • Serial number equals
        • SEEPROM write error
      • Collisions
      • Resume state
      • Run-length coding
  • DXS
  • The SlinkX ActiveX control
    • Using DCOM
    • Methods, Properties, and Events
      • AddDevice
      • AddDeviceText
      • Connect
      • DeleteDevice
      • Disconnect
      • GetCodeName
      • GetDeviceName
      • GetNumCodes
      • NumCM11As
      • NumDevices
      • NumDXSs
      • NumSlinkes
      • ReportNoMatch
      • Send
      • SendEx
      • SlinkeDeviceEvent
    • Low-Level Device Interface
      • Setting the baud rate
      • Transmitting a S-Link message
      • Transmitting a S-Link bit-mode message
      • Transmitting an IR signal
      • Enabling the IR transmitter ports
      • Enabling the IR receiver ports
      • Setting the IR receiver port polarities
      • Setting the IR routing table
      • Setting the IR minimum message length
      • Setting the IR timeout period
      • Setting the IR sampling period
      • Setting the IR carrier frequency
      • Sending data out the parallel port
      • Setting the parallel port bit directions
      • Setting the parallel port handshaking mode
      • Sampling data from the parallel port
      • Receiving signals from IR ports
      • Receiving a S-Link message
      • Receiving a S-Link bit-mode message
      • Receiving data from the parallel port
    • CM11a X-10 Interface
    • Revision Log
  • CDJ
    • Using the list views
    • Searching for music
      • How to make a search query in CDJ
    • Playlists
      • Adding music to a playlist
      • Re-arranging playlists
      • Shuffling a playlist
      • Optimizing playlist alternation
      • Controlling playback of a playlist
      • Saving and loading playlists
      • Selecting items in a playlist
      • Locating discs
      • Adding images to discs or tracks
      • Adding mp3 files to the CD library
      • Adding lyrics
      • Uploading text to the players
      • Creating a log file
      • Searching for S-Link codes for Sony equipment using CDJ
        • Identifying the ID code of the device
    • Using Event Maps
      • Adding Devices to CDJ
      • Loading Event Maps
    • 1
      • Commands and Responses
    • Revision Log
    • Port Diagnostics
    • Revision Log
  • 1